Zippers-performance 117-449 Manuel d'utilisateur télécharger pdf

Installation Instructions for Zippers

Max Flow Air Cleaner # 117-448

High Flow Air Cleaner # 117-449

List of Materials

(1) Gasket, carb to a/c backplate (1) Air filter element

(4) Air cleaner backplate o-rings (3) Air filter mounting stanchions

(2) breather bolts (3) Torx head cap screws

(1) Air cleaner backplate (1) Air cleaner inner cover washer

These kits are designed to be used on Twin Cam® engines equipped with the standard Twin Cam®

“football” air cleaner cover, which makes 360º contact between the cover back and the rubber gasket on

the filter. Do not install decorative cover inserts (due to increased weight) or use 2006-up CVO Touring

model covers that do not make 360º contact between the cover back and the rubber gasket.

1. Remove existing air cleaner assembly, including backplate and black support bracket.

Retain factory supplied cover and mounting screw (bracket is not re-used).

2. Place new gasket onto backplate, aligning holes and mounting studs.

3. Install (2) o-rings into counterbores on backplate where backplate meets cylinder head

(a dab of grease will hold them in place during installation). Place backplate over throttle body

with gasket in place. Apply low strength threadlocker such as blue Loctite® to stanchion studs

and loosely attach backplate to throttle body or carburetor (do not tighten yet).

4. Install (2) o-rings over supplied breather/support bolts into recessed area under the bolt

heads. Apply low strength threadlocker such as blue Loctite® to support bolt threads; install

bolts through backplate into cylinder heads. Tighten support bolts to 120-140 in/lbs (13.5-16.0

Nm). Tighten (3) stanchions through backplate into throttle body and tighten to 85-90 inch

pounds in a sequence. Due to the thickness of the backplate gasket, perform several

rounds of the tightening as the gasket will crush and relax the torque on the stanchions.

3-4 tightening rounds should be performed to ensure proper torque.

5. Apply low strength threadlocker such as blue Loctite® to (3) Torx head screws provided

and install filter element to stanchions.

6. Re-install the air cleaner cover bolt through the cover. Dab a small

amount of silicone seal to one side of the supplied thick washer. From

inside the cover, place the supplied washer over the bolt, silicone side

towards air filter element. Apply Loctite on the threads of the bolt and

install the cover assembly onto the air filter element.

This product is legal in California only for racing vehicles which may never be used upon a highway.

Place washer

inside cover

Tips For Cleaning Your Max Flow Filter Element

Gently shake off

and brush away

excess dirt.

Spray on

Cleaning

Solution so that

the filter is fully saturated,

and let soak for 10 minutes.

Rinse filter from the clean

side to the dirty side until

water comes through clear.

Use only low pressure from a

tap or hose.

Allow filter to

dry. A fan may

be used to

speed process.

DO NOT use

heated air blowers,

compressed air, or open

flame.

Make one

careful

application of

Filter Oil to each

filter pleat.

Allow oil to seep

into filter for 20 minutes.

Re-oil any areas that still

appear dry. Do not over oil.

Thank You for Purchasing a Zippers Performance Product!

Place washer 1

Résumé du contenu

Page 1 - Place washer

Installation Instructions for Zippers Max Flow Air Cleaner # 117-448 High Flow Air Cleaner # 117-449 List of Materials (1) Gasket, carb to a/c back

Modèles reliés 117-448

Commentaires sur ces manuels

Pas de commentaire

Zippers-performance 117-449 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Zippers-performance 117-449. Zipper's Performance 117-449 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés 117-448

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Zippers-performance 117-449